Furniture Lighting 12-24V

New

SKU: PA-GLAXMNKW-AL-20M

Profile GLAX MINI high for LED strip, surface-mounted, 2 m, black

During operation, the LED strip generates heat that must be dissipated from it. Otherwise, the tape may wear out prematurely. Special aluminium GLAX profiles are used to dissipate heat from the belt. In order to effectively dissipate heat from the tape to the aluminum profile, the tape must adhere to it with its entire surface. Therefore, before pasting the LED strip into the GLAX profile, it is necessary to degrease its center. Applied profiles are very often chosen by customers due to the very simple assembly. In the case of the micro profile, special mounting brackets are used, having small, curved blades that hold the profile in place. It is recommended that the distance between the grips is not more than 1 meter. The mounting brackets are screwed to the selected surface with screw Ø 3 with a conical head. It is very important that the diameter of the screw head does not exceed 6 mm. The mini, high profile allows you to get an even line of light without visible light points even when using a tape with a not very dense arrangement of LEDs. The maximum width of the LED strip is 10 mm.

New

SKU: PA-GLAXMNKW-AL-90

Profile GLAX MINI high for LED strip, surface-mounted, 2 m, champagne

New

SKU: PA-GLAXMNKW-AL-10

Profile GLAX MINI high for LED strip, surface-mounted, 2 m, white

New

SKU: PA-GLAXRAD-AL

Profile GLAX RADIATOR for LED strip, 2 m

During operation, the LED strip generates heat that must be dissipated from it. Otherwise, the tape may wear out prematurely. Special aluminium GLAX profiles are used to dissipate heat from the belt. In order to effectively dissipate heat from the tape to the aluminum profile, the tape must adhere to it with its entire surface. Therefore, before pasting the LED strip into the GLAX profile, it is necessary to degrease its center. The profile with heatsink is able to effectively absorb the heat generated by very high power tapes, consuming up to 30 W / 1m. Using the lens cover, we have the ability to narrow the angle of light scattering to 60 °. Applied profiles are very often chosen by customers due to the very simple assembly. In the case of the micro profile, special mounting brackets are used, having small, curved blades that hold the profile in place. It is recommended that the distance between the grips is not more than 1 meter. The mounting brackets are screwed to the selected surface with screw Ø 3 with a conical head. It is very important that the diameter of the screw head does not exceed 6 mm. Specially designed design allows you to hang the profile on cables. Dedicated links are 150 cm long.

New

Radio controller MONO for LED strip, DC12-24V, max. 120-240 W, 1-zone

SKU: LD-KONML-MONO

Radio controller MONO for LED strip, DC12-24V, max. 120-240 W, 1-zone

A remote light control system consists of three essential components: A single controller is one zone (up to 4 controllers can be paired in the control device), to which two light sources can be connected: LED strip or LED fitting. Connecting the components to the controller is very simple. On one side, the cables from the LED driver (12/24 V) are connected. These must be cables with uninsulated ends. On the other side, there is a place to insert cables from light sources. Cables with uninsulated ends are also inserted here, remembering about the correct polarity. After tightening all the terminals, the controller is ready to be paired with the control device. The maximum load of the controller is:

New

Radio controller RGBW for LED strip RGBW, DC12-24V, max. 120-240 W, 1-zone

SKU: LD-KONML-RGBW

Radio controller RGBW for LED strip RGBW, DC12-24V, max. 120-240 W, 1-zone

A remote light control system consists of three essential components: A single controller is one zone (up to 4 controllers can be paired in the control device), to which both RGB and RGBW LED strips can be connected. Connecting the components to the controller is very simple. On one side, the cables from the LED driver (12/24 V) are connected. These must be cables with uninsulated ends. On the other side, there is a place to insert cables from the light source. Cables with uninsulated ends are also inserted here, remembering about the correct polarity. After tightening all the terminals, the controller is ready to be paired with the control device. The maximum load of the controller is:

New

Remote control for radio controller MONO, 4-zone

SKU: LD-KONML-MONO-PIL

Remote control for radio controller MONO, 4-zone

A remote light control system consists of three essential components: A remote control is one of the two available control devices. The remote control can be used to control 4 zones independent of each other. Many single controllers responsible for a single light point can be assigned to each zone. The remote control is powered by two AAA batteries (not included in a set). On the remote we will find: Zone coding It is necessary to determine to which zone of the remote control the controller is to be coded. Then we disconnect the power supply of the controller for at least 10 seconds. After reconnecting the power supply, the ON button of the selected zone should be pressed 3 times within 3 seconds. Correct pairing is signalled by the LED strip blinking 3 times. To activate the night lighting function, that is, the maximum dimming of the LED strip, the OFF Master or OFF button of the selected zone should be held.

New

Remote control for radio controller RGBW, 4-zone

SKU: LD-KONML-RGBW-PIL

Remote control for radio controller RGBW, 4-zone

A remote light control system consists of three essential components: A remote control is one of the two available control devices. The remote control can be used to control 4 zones independent of each other. Many single controllers responsible for a single light point can be assigned to each zone. A remote control is powered by two AAA batteries (not included in a set). On the remote we will find: Zone coding It is necessary to determine to which zone of remote control the controller is to be coded. Then we disconnect the power supply of the controller for at least 10 seconds. After reconnecting the power supply, the ON button of the selected zone should be pressed 3 times within 3 seconds. Correct pairing is signalled by the LED strip blinking 3 times. To activate the night lighting function, that is, the maximum dimming of the LED strip, the OFF Master or OFF button of the selected zone should be held. To turn on white colour, the ON button should be held longer.

New

SKU: PA-ZASGLAXMNKO-00

Round plug for surface-mounted profile GLAX MINI, (set of 10 pcs.), gray

The end end cap for LED profiles is an accessory that is used to protect the ends of the LED profiles and at the same time prevent dirt and insects from getting inside the profile. The end end plugs are made of ABS plastic, which ensures durability and resistance to mechanical damage. The end end cap for LED profiles is very important because it not only protects the ends of the profiles, but also helps to maintain the aesthetics of the entire LED installation. Thanks to the use of end plugs, the installation looks more neat and professional. It is also important that the end caps are well matched to the LED profile, which will avoid possible light clearances.

New

Screw touch switch, max. 500 W, AC220-240V, IP20, 2 m

SKU: AE-WBEZDK15-10

Screw touch switch, max. 500 W, AC220-240V, IP20, 2 m

New

SKU: PA-ZGLAXKTOMZ-00

Set GLAX corner (profile, plugs, diffuser)

A high-quality angular profile set, ideal for use in furniture corners, especially under hanging cabinets in the kitchen and under the shelves in the dressing room. Installation of the angular profile is simple and convenient. Just paste it with mounting glue or silicone into the appropriate corner. The set includes an angular profile, a cover that gives the entire structure an aesthetic look, and two end caps that close the ends of the profile safely and aesthetically. Thanks to this, we will achieve not only functionality, but also aesthetic finish of each corner.

New

SKU: PA-ZGLAXOMZ-00

Set GLAX recessed (profile, plugs, diffuser)

A modern and functional mortise profile kit that is ideal for obtaining a smooth and aesthetic surface in a variety of applications. Our mortise profile is the perfect solution where collision-free integration with other elements such as drawers or drawer fronts is required. Profile assembly is extremely simple and does not require the use of mounting adhesives or silicones. It is enough to carry out milling with a width of 15 mm and a depth of at least 5 mm to prepare the right groove. Then the profile can be easily pressed into the prepared groove. Thanks to special teeth on the profile, we will ensure a safe and durable fixation that will not protrude beyond the edge of the board. The set includes a profile that ensures the stability and solidity of the structure, a cover that gives the entire structure an aesthetic look, and two end caps that close the ends of the profile safely and aesthetically.

CART